evo ga i novi update za phoenix

http://rapidshare.de/files/20879835/phoenix_service_sw_2006_12_7_138_upd.exe.html

nisam ga josh skinuo... pa ako neko skine i proba, neka javi sta je novo..

DON´T: install data packages or phoenix without deinstalling old one before

DON´T: install more than one phone type without restarting your pc.

DON´T: downgrade FLS-4 drivers if asked during installation of data packages

DON´T: use WIN XP Home Edition (works, but more troubles than XP PRO or WIN 2K)

DON´T: use usb hubs for data cables (dku-2...)

DON´T: use notebooks with port replicators for parallel port

DON´T: use nokia pc suites parallel to phoenix, may cause driver violation

DON´T: use pc for other purpose during flash process

DON´T: downgrade any type of phone, it´s a good chance to kill phone

DON´T: start flash process on 7650 before boot process has finished, may kill phone

DON´T: deplug phone during flash process, may kill phone

Možda nekom pomogne ako se flash zaustavi na određenom procentu:

Communication to product not working!


Corrective Action:
1. Remove charger if connected.
2. Remove battery.
3. Install battery back.
4. Boot up the phone to normal mode from power key by keeping also the buttons green call button,
number 3 button and star button pressed and keep those buttons pressed until you see the hands or PIN query on the screen.
5. Connect charger if needed.
6. Enter PIN code if requested.
7. Set home country, time and date if requested.
8. Wait until the phone is booted up to normal mode.
9 Press OK => flashing will continue

gdje ovo naći ja zasad neuspješno tragam

to je fajl potreban za vraćanje u život ubijenih RM-1
nigdje ga nemogu nać Erase_rap_adl_loader_modatty_b y_trk.zip

sacemo da vidimo samo da ja to sa mojih 3kbs skinem

 

1. Start Phoenix. Do not try to scan product or open product.
2. Choose Flashing -> SW Update
3. Select Browse and select directory where you saved the "erase file" *****
4. When file has been selected, press Start
5. At this moment Phoenix gives error-message, but press Yes to start
flashing.
6. When flashing is completed there might come screen where user is
instructed to turn power on to phone. If this kind of screen appears press
Cancel.
7. After erase file has been successfully flashed, you must flash device with
correct device software.
8. Flashing files must be selected manually because device is not yet fully
functional
9. Select right files for Image File and PPM File boxes
- Image File is typically in c:\Program Files\Phoenix\Products\RM-1\
directory and filename ending is .C0R
- PPM File is typically in the same directory as Image File. E.g. Euro
1 variant PPM file ending is .v02. At this moment it is possible to
select any PPM file because phone must be flashed one more time
to ensure that device is returned to customer with correct variant
10. When right files are now selected to Image File and PPM File Boxes press
Start.
11. Most likely Phoenix gives an error message after pressing start, but this is
normal. Press Yes and flashing continues.
12. When device is successfully flashed, close SW-Update screen
13. Now Phoenix recognize RM-1 device normally
14. Choose Flashing -> SW-Update
15. Phoenix reads device product code and selects right image file and variant
for the phone
16. Press Start and wait until flashing is done
22. RM-1 device is now fully functional again.

Ciglo HVALA za ovo,inače cijelo uputstvo za oživljavanje je isprintano i proučeno samo treba pristupit poslu

Ako ovo uspe, častiš klopu @nikola34!

Gdje ga izceprka????...svaka cast... ja zamal sinoc da se obrukam

častim brate po Symbianu.