imam problem sa downloadom, bez obzira koji manager korsitim, probao sam sa free download mangerom, jdownload, i iz mozile. Kada im zadam da smeste na D particiju izbaci mi ovu poruku,

i zamrzne se win. samo restart, ovaj sam problem imao i prilikom kopiranja koji sam resio ovde na bureku, dodao sam neki kljuc i posle toga je sve bilo ok, jedno 10 dana, sada kopiram bez problema sa particije na particiju, ali download nece.
A na C praticiju FDM i mozzila downloaduju bez problema
Stavio sam svez sistem pre 4 sata i dalje se, posto sam mislio da je do njega, skenirao sa HDD regenratorom, nema nijdenog bad sectora, nemam pojma sta vise da uradim. da li problem moze da bude bios ili hard oce da otegne papke.
Jos da kazem da je instalacija win-a i formatiranje C particije prosla bez problema, instalacija programa i drajvera

Da li si probavao ovo i ovo?

uradio sam ovo
   1.  Click Start, and then click My Computer.
   2. Right-click the hard disk, and then click Properties.
   3. Click the Hardware tab.
   4. Click to select the hard disk, and then click Properties.
   5. Click the Policies tab.
   6. Click to clear the Enable write caching on the disk check box, and then click OK.
   7. Click OK to close the Local Disk (C:) Properties dialog box.
   8. Repeat steps 3 through 5 for each hard disk that is installed in your computer.

     i ovo
   1. Click Start, right-click My Computer, and then click Properties to open the System Properties dialog box.
   2. Click the Advanced tab, and then under Performance, click Settings to open the Performance Options dialog box.
   3. Click the Advanced tab.
   4. Under Memory Usage, click to select Programs, and then click OK.
   5. Click OK to close the System Properties dialog box.

i ovo

   1. Click Start, click Run, type regedit, and then click OK.
   2. Locate the following registry key:
      HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management
   3. In the details pane, right-click the SystemPages value, and then click Modify
      Note Default value is 0 (hex)
      .
   4. In the Value data box, type 7FFF, and then click OK.
      Note You could try using the following alternate values:
          * 7FFF = 32,000
          * PTEs BFFF = 50,000
          * PTEs 24FFF = 150,000 PTEs

      Note The FFFFFFFF value should not be used. If you set it too high, you might run out of paged pool memory.
   5. Exit Registry Editor.
   6. Restart
   7. Monitor the Memory \ Free System Page Table Entries in Perfmon.

i za sada prvih nekoliko testova prolazi bez problema, mada jos nista nije sigurno, posto nema pravila nekad se dogodi nakon 3-4MB, a nekad nakon 200MB.
nocas cu ga testirati, pa cemo videti

i ponovo je se dogodilo , imam takvu zelju da ga skrcam, maltretiramse sa ovim  vec 4 dana


sad sam probao ovo

To work around this problem you must set CacheControl to zero:

   1. Click Start, click Run, type regedit, and then click OK.
   2. Locate and then click the following key in the registry:
      HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\3ware Storage Controller\Cache Control
   3. On the Edit menu, click Modify.
   4. Type 0, and then press ENTER.
   5. Quit Registry Editor.

ali nemam 3ware storage controller u control-u

prilikom downloada mi izbaci i ovo

ima li neko ideju sta da probam jos

uradjeno i ovo

To work around this problem you must set CacheControl to zero:

   1. Click Start, click Run, type regedit, and then click OK.
   2. Locate and then click the following key in the registry:
      HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\3ware Storage Controller\Cache Control
   3. On the Edit menu, click Modify.
   4. Type 0, and then press ENTER.
   5. Quit Registry Editor.

uz pomoc cmd-a

To restore normal behavior:

1. Open a CMD.exe window.
2. Type the following command and press Enter:
REG ADD "HKLM\SYSTEM\CurrentControlSet\Control\3ware Storage Controller" /V CacheControl /T REG_DWORD /D 0 /F
3. When you receive the The operation completed successfully message, shutdown and restart Windows XP
i opet labud.

Instalirana tri hotfixa sa microsoft suporta, i nista.

Uradjen reinstal IDE kontrolera, i naravno opet nista

Na kraju pokusana instalacija SP3, posto sam nakon 48h trazenja resenja primetio da problem imaju ljudi koji imaju maxtorHD i XP sa SP2.
Posle inastalcije SP3 racunar se zakucavao pri boot-ovanju, na kraju uradio restore sa acronis-om,i sad sam na pocetku.
Nije mi jasno radi na C particiji, a na D nece, i ako je isti hard, prilikom kopiranja vecih fajlom, izbaci da ce za jedno 120 minuta da zavrsi, 3GB je bila velicina fajla

Jos nisam proba da formatiram D particiju, mada ne verujem da ce da se nesto promeni

jedino nisam uspeo da ovo uradim tj nadjem

Kod mene je ovaj kabal, to je valjda serial ATA


Method 1: Check that you are using an 80-wire, 40-pin cable
Make sure that your UDMA hard disk controller is using an 80-wire, 40-pin cable. For information about how to do this, see the documentation that is included with your computer, or contact your UDMA hard disk controller manufacturer.

If you are using an 80-wire, 40-pin cable, go to method 2.
If you are not using this cable, obtain and use an 80-wire, 40-pin cable, and then test to determine whether this resolves the error message.

If this resolves the error message, you are finished.

If this does not resolve the error message, go to method 2.
Method 2: Check the BIOS settings
Warning Do not change the BIOS settings unless you are very familiar with all the effects of changing BIOS settings.

Make sure that the BIOS settings are not configured to force faster UDMA modes. For information about how to do this, see the documentation that is included with your computer, or contact your computer manufacturer.

If the BIOS settings are not configured to force master UDMA modes, go to the "Delayed Write Failure information" section for information about additional measures that you can take to prevent the "Delayed Write Error" message from recurring.
If the BIOS settings are configured to force master UDMA modes, change the settings, and then test to determine whether this resolves the error message.

If this resolves the error message, you are finished.

If this does not resolve the error message, go to the "Delayed Write Failure information" section.